PREFABRICATED PORTABLE UNIT

 

SPECIFICATIONS

 

GENERAL

 

THE PORTACABINS ARE DESIGNED TO PROVIDE INSTANT ACCOMMODATION ESPECIALLY SUITABLE FOR SITE PROJECTS IN THE GULF CLIMATIC CONDITIONS COMBINING THE ADVANTAGES OF OCCUPYING MINIMUM OF SPACE AND TIME FOR ERECTION.  THE UNIT FEATURES AESTHEtIC FINISHES WITH INTERNAL FITTINGS FACTORY-INSTALLED, REQUIRING EXTERNAL HOOK-UP TO EXISTING SERVICES AT PROJECT SITE.

  

FLOOR

 

FLOOR CHASSIS IS FULLY FABRICATED WITH MS STEEL. 100x50mm MS channel PERIMETER frame with longitudinal MS I-beam in the centre & lateral MS I-beam at 2m intervals. Flooring is 18mm ‘korindo’ plywood FIXED WITH rivetS on 50mmx50mm MS angle joists. FLOORING IS heavy-duty vinyl-FLOORING WITH heat-welded joints. ALL STEEL FRAMING IS PRIMED WITH  RED-OXIDE AND FINISHED WITH TWO COATS OIL-BASED ENAMEL GLOSS PAINT.

  

WALLS

 

Wall panel is 57mm thick, sandwich-type pre-pressed paNEL, with 6mm ‘korindo’ plywood externally FIXED on 47mm x 50mm timber stud-frame and decorative woodgrain style plywood on internal walls. Insulation is rigid 47mm polystyrene BOARD. EXTERNAL WALL SURFACE IS COATED WITH ALL-WEATHER HEAVY-TEXTURED PAINT APPLIED ON UNDERCOAT PRIMER, PLUS PROTECTIVE WATERPROOF OIL-BASED TOPCOAT. AIR-COND APERTURES ARE STANDARD FITTED WITH STEEL SUPPORT BRACKETS.

 

TOILET/KITCHEN WALL FINISH IS PAINTED WIITH TWO COATS WATERPROOF ENAMEL PAINT WITH SKIRTINGS SUITABLY SEALED WITH SILICONE SEALANT.

 

ROOF/CEILING

 

26G CORRUGATED ALUMINIUM SHEETING FIXED WITH BITUMEN-WASHER ROOF NAILS ON WHITEWOOD PURLINS. ROOF TRUSSES ARE DOUBLE PITCHED AT 2.4m SPACING. CEILING IS SUSPENDED TYPE WITH 6mm BOARD and beadings along the joints, finished with white light-textured paint.  ROOF CAVITY IS INSULATED WITH 50mm POLYSTYRENE INSULATION.

 

DOORS

 

200x90 SEMI-SOLID, FLUSH TYPE SET IN MERANTI FRAME, FITTED WITH ‘UNION’ LOCK AND 3 brASS HINGES. INTERNAL SURFACE IS DECORATIVE BOARD TO MATCH WITH WALL FINISH. External finish is two coats enamel gloss paint applied on 4mm plywood

 

WINDOWS 

 

90cm x 90cm ANODISED, ALUMINIUM-FRAMED (‘AL GHURAIR’), HALF-SLIDING, WITH 6mm CLEAR GLASS AND INSECT SCREEN. EXHAUST WINDOWS ARE 60cm x 30cm fixed type with 6mm frosted glass panel.

  

ELECTRICAL  (Complying with ‘DEWA/IEE’  Standards)

 

Cables are ‘DUCAB-BICC’ conduited and concealed.

 

               - 1.5 mm  - lighting

               - 2.5 mm - 13 amp sockets

               - 4.0 mm - 15 amp sockets

 

Fittings include:

 

               - 2x36W fluorescent fixtures (JAPAN)

               - external waterproof bulkhead light (German)

               - 13 amp and 15 amp A/C plug sockets (UK)

               - water heater 12 gallons ("EverHot” UAE)

               - extractor fans (JAPAN)

               - light switches (UK)

               - distribution board with MCBs & ELCB (‘MEM’)

 

PLUMBING/SANITARY

 

½" copper and PVC pipes to provide hot/cold system. Fittings include Western WC, urinals, washbasin with mirror, shower tray (80x80) with curtain, 1m SINGLE-BOWL stainless steel kitchen sink CABINET with Mixer and waste fittings.  SINGLE 3/4" valve to be provided externally for on-site connection.

 

OPTIONAL

1.

ACCOMMODATION/OFFICE FURNITURE.

2.

AIRCONDITIONING UNITS (WINDOW OR SPLIT-TYPE).

3.

CONCRETE FOOTINGS/SITE INSTALLATION/ERECTION. 

4.

PVC DRAINAGE CONNECTON INTO EXISTING SYSTEM (OR EXCAVATION & INSTALLATION OF FIBREGLASS

SEPTIC TANK & PVC CONNECTION).

5.

FRESH WATER CONNECTION FROM EXISTING SUPPLY POINT (OR PROVISION OF FIBREGLASS OVERHEAD WATER STORAGE TANK & CONNECTION).

6.

POWER CONNECTION VIA EXPOSED CONDUITED CABLE OR TRENCHED ARMOURED CABLE,SUITABLY CONNECTED FROM AN ISOLATOR SWITCH PROVIDED AT THE EXISTING MAINS DISTRIBUTION BOARD.
 
 
 
 
 
visit IT Infinity